Scallop-Lapel Bell-Sleeve Mesh Robe, Satin Belt and Thong Set

Layer scalloped lapels over a bell-sleeve mesh robe

This scallop-lapel bell-sleeve mesh robe, satin belt and thong set concept contains exactly three separate pieces. The smoky-plum open-front robe presents two charcoal floral-lace lapels, wide three-quarter bell sleeves and lace cuffs, accompanied by one loose satin belt and one matching lace thong.

The image establishes visible styling only. It does not confirm graded measurements, fibres, opacity, stretch, belt fit, rear construction, gusset, care or production readiness.

Audit the exact three-piece pack

Count one robe, one separate waist belt and one thong before sealing. Bra, brief, stockings, garter belt, gloves, jewellery and other styling accessories are excluded.

Match the three pieces by size and colour code, smoky-plum dye lot, charcoal trim, thread and floral motif. Record the complete set against a traceable packing lot.

Measure both scalloped floral-lace lapels

Record lapel length, maximum width, scallop depth, motif repeat, edge finish and attachment seam on left and right. Compare the two panels for mirrored placement and equal extension from neckline to hem.

Reject clipped motifs, broken yarns, puckering, mismatched scallops, rough thread and abrupt bulk at the lower lapel ends.

Map the open-front robe body

Measure centre-back length, front length, shoulder width, bust span, waist span, hip span, front overlap potential and sweep at the hem. Record each dimension for every graded size.

Short, relaxed and wrap-fit language remains pending the approved wearing-position study and the belt-range map.

Measure both wide bell sleeves

Record sleeve length from shoulder, upper-arm circumference, elbow width, cuff opening, flare angle and mesh extension. Compare left and right sleeves for equal drape, seam placement and hem level.

Check that the widening sleeve does not twist at the underarm or pull the robe lapels out of alignment.

Inspect the floral-lace sleeve cuffs

Measure cuff depth, circumference, motif placement, scallop edge and seam bulk on each sleeve. Test the lace-to-mesh junction under bounded movement and care conditioning.

Reject sharp applique ends, loose floral elements, broken mesh bridges and cuffs that differ beyond tolerance.

Characterize the smoky-plum sheer mesh

Record fibre content, mass, openness, thickness, extension and permanent set in warp, weft and bias directions. Inspect body and sleeves for snags, holes, skew, hard inclusions and uneven dye.

Sheer, breathable, soft and skin-friendly claims remain pending exact construction and performance evidence.

Audit hem, shoulders and side seams

Map stitch type and density at shoulders, armholes, underarms, side seams, lapels, cuffs and the softly flared hem. Measure seam slippage after bounded stretch and validated care cycles.

Reject skipped stitches, raw mesh, needle damage, bulky overlap, rough thread and a hem that ripples outside the approved appearance tolerance.

Document the unseen rear construction

The front flat lay does not reveal centre-back shaping, shoulder-blade ease, rear hem, belt-loop position or any back seam. Require a rear technical view, pattern pieces and graded finished measurements.

Backless, seamless-back and contouring descriptions are excluded until the approved sample is documented.

Measure the separate satin waist belt

Record total length, width, thickness, seam location, end finish, tensile behaviour and knot bulk. Check both faces for pulls, shine variation, edge waviness and colour transfer.

The belt is a garment closure only. It is not a restraint, leash, handle or body-weight support and must never be tied around the neck.

Validate belt loops and waist overlap

The visible flat lay does not confirm belt loops. Require loop count, position, dimensions and attachment strength, or document a loop-free design if that is the approved construction.

Build waist guidance from robe overlap and belt length at each size. Do not claim universal fit without graded samples and knot allowance.

Measure the matching thong and gusset

Record front height, back geometry, crotch width, side-strap range, lace coverage, binding and seam bulk. Require a rear view before describing back coverage.

Document gusset length, width, fibre content, layer count and attachment stitches. Cotton, breathable, hygienic and moisture-management claims remain pending the final specification and tests.

Identify mesh, lace, satin and trims

Obtain fibre declarations for robe mesh, lapel lace, cuff lace, belt face, belt core, thong lace, side straps, bindings, thread and gusset. Test all components for dry and wet rubbing, perspiration and wash migration.

Silk, satin fibre, hypoallergenic, sustainable and certification claims remain pending exact composition and traceable evidence.

Build sizing and care from approved garments

Combine robe body, sleeve, cuff, belt and thong measurements with extension and recovery data. Do not map supplier letter sizes directly to retail or infer fit from a flat lay.

Use only the validated mild wash and drying method for the final mesh, lace, satin, elastics, thread and gusset. Keep the belt separate during cleaning if the care study requires it; avoid bleach, solvents, wringing, high heat and direct ironing unless approved.

Build landed price from sheer-robe benchmarks

An Alibaba robe-lingerie category page displayed a four-piece satin and lace robe set at USD 3.96 to 4.29 with MOQ 3, and a separate sheer robe set at USD 7.50 to 8.00 with MOQ 2. Another bulk page displayed a sheer mesh lace robe set at USD 6.31 with MOQ 5. These are broad procurement references, not this exact bell-sleeve lapel construction or an approved supplier.

The public procurement benchmark supports an EUR 42.99 planning price after provisional allowance for China-origin freight, graded samples, sheer mesh, two scallop lapels, two lace cuffs, separate satin belt, thong, gusset, seam, colourfastness and care validation, discreet fulfilment and apparel handling loss. Exact supplier, quote, MOQ, sizes, colours, fibres, packed weight, freight, duty, tax, certification, payment terms and lead time remain pending.

Frequently asked questions

How many pieces are included?

Exactly three: one open-front robe, one separate satin belt and one thong.

Are the sleeves full length?

The concept shows wide three-quarter bell sleeves, but the graded sleeve length remains pending.

Is the belt attached to the robe?

No. One separate untied belt is planned; belt-loop construction remains pending the approved sample.

Is a bra included?

No. Bra, stockings and other styling accessories are excluded.

What sizes will be offered?

The size range and every graded robe, sleeve, belt and thong measurement remain pending supplier confirmation.

How should the set be washed?

Follow only the validated care label for the approved mesh, lace, satin, elastics, thread and gusset.