FHTF SM044 Detachable 60 cm Spreader Bar Cuff Kit: 2 Colours

SM044 is tied to one exact FHTF wholesale offer

This page maps to Ningbo Fuho Ascend Import & Export Co., Ltd., Alibaba offer 60770321201, FHTF brand and model SM044. Seven retained supplier images show the same detachable polished bar, four padded buckle cuffs and clip hardware.

Black and black-and-red are genuine order choices

The inspected order panel exposes Black and Black & Red. Each storefront variation uses its matching supplier image, so the colour choice remains traceable when requesting a quotation or checking an incoming carton.

Finish tolerance, lining shade and batch consistency remain pending approved samples.

The bar is presented as three detachable 20 cm sections

An exact supplier diagram labels three metal tube sections at 20 cm each. The assembled identification length is therefore about 60 cm before allowing for joints and end hardware.

This is a supplier-presented dimension, not a tolerance-controlled drawing. Thread direction, locking method, assembled length and joint play require physical inspection.

Wrist cuffs carry a supplier-printed 20 to 30 cm range

The wrist-cuff diagram labels each cuff 5.8 by 35 cm and shows an adjustable circumference range of 20 to 30 cm. Multiple buckle holes and a padded inner band are visible.

Measure usable circumference, overlap and buckle engagement on approved samples. Printed dimensions do not prove comfort or fit for every wearer.

Ankle cuffs carry a supplier-printed 25 to 35 cm range

The ankle-cuff diagram labels each cuff 5.8 by 40 cm with a 25 to 35 cm adjustment range. The exact black image shows the same buckle, rivet and D-ring layout used across the set.

Check that padding remains between skin and every edge throughout the approved range. Do not force a cuff onto a body area outside its measured fit.

Four cuffs connect through clips and swivelling rings

The gallery shows four padded cuffs linked to attachment points through metal clips and ring hardware. This permits the components to be detached for setup, inspection and storage.

Clip gate closure, ring welds, rivet security, swivel movement and corrosion resistance are not published specifications and must be checked lot by lot.

Consent and immediate release come before positioning

Agree on the arrangement, intensity limits, stop word and nonverbal signal before fastening any cuff. Keep every buckle and clip accessible to both partners.

Never leave a restrained person alone. Release at once for panic, breathing difficulty, tingling, numbness, coldness, colour change or pain.

Stainless steel and PU leather are marketplace declarations

The public page lists stainless steel plus PU leather. It does not identify steel grade, coating chemistry, backing textile, foam, adhesive, thread, rivet alloy or nickel content.

No medical-grade, hypoallergenic, vegan, latex-free or certification claim is made without model-specific documents and approved samples.

Waterproof wording does not establish immersion safety

The structured listing uses waterproof wording but provides no test method or scope. Padded seams, rivets, buckle holes, metal joints and tube interiors may retain moisture.

Do not immerse the set or treat it as shower equipment until the supplier provides written SM044 care instructions and relevant evidence.

Cleaning should protect padding and metal joints

Until the approved manual arrives, wipe compatible surfaces with mild soap and a damp cloth, remove residue, dry every seam and connector fully and store the bar disassembled in a ventilated dry place.

Avoid solvents, bleach, abrasive pads, prolonged soaking and high heat. Inspect for odour, delamination, corrosion and trapped moisture before reuse.

Fit checks must continue throughout use

Begin with a loose setting and verify normal breathing, skin colour, temperature and sensation. Recheck frequently because movement can change pressure even when the buckle position stays fixed.

Use the wrist and ankle labels only as identification guidance. Individual anatomy, padding compression and clothing thickness can change practical fit.

Assemble the bar before anyone enters the cuffs

Join all three sections on a clear surface, confirm each joint is fully engaged and test every attachment point by hand at very low force. Attach empty cuffs and map the fastest release sequence before fitting a person.

Stop if a section loosens, a clip gate sticks, a ring distorts or a rivet moves.

This kit is not load-bearing or suspension equipment

The offer provides no safe working load, breaking strength, dynamic-load test or certification for suspension. The bar and cuffs are intended only for low-tension adult positioning on a stable surface.

Never use the set for climbing, hanging, lifting, fall arrest, neck restraint, chest compression or body-weight support.

Incoming inspection must match offer 60770321201

Verify FHTF model SM044, ordered colour, three 20 cm bar sections, two wrist cuffs, two ankle cuffs, attachment hardware and the retained exact supplier images. Require the same identification on the quotation, invoice and carton label.

Quarantine sharp edges, exposed staples, incomplete stitching, loose rivets, cracked coating, deformed clips, damaged threads, missing pieces or unapproved material and colour changes.

EUR 49.99 includes a provisional China-to-Portugal reserve

On 11 August 2026 the offer displayed EUR 8.90 for 5 to 9 pieces, EUR 8.82 for 10 to 499 and EUR 8.45 for 500 or more. A planned 200-unit order therefore references EUR 8.82 per set before logistics and import costs.

The page listed a 25 by 15 by 15 cm single package and 0.8 kg gross weight, while the visible five-piece delivery estimate was not a 200-unit freight quotation. EUR 49.99 is a planning retail price, not a confirmed landed cost.

Frequently asked questions about FHTF SM044

What colours can I select?

Black and Black & Red are the two supplier-linked choices shown on the inspected offer.

How long is the assembled bar?

The supplier shows three 20 cm sections, indicating about 60 cm before joint and end-hardware tolerances are confirmed.

What are the cuff ranges?

Supplier diagrams state 20 to 30 cm for wrist cuffs and 25 to 35 cm for ankle cuffs. Sample measurement and personal fit checks remain essential.

Can this set support body weight?

No. No load rating or suspension certification was supplied, so body-weight support is outside the approved use boundary.

Is it safe to immerse?

Not confirmed. Waterproof wording appears on the marketplace page without a defined test scope.

Is EUR 49.99 the final launch price?

No. It is a planning price pending samples, packing data, a 200-unit quotation, freight, clearance, duty, VAT and purchasing terms.