Emerald Crown-Collar Curved Vibrator

A continuous curve defines the whole format

The crown collar curved vibrator concept uses a broad rounded tip, an uninterrupted emerald body and a compact base control. Its bend is the defining feature, so shoppers need measured dimensions and a true side profile rather than generic claims about targeted contact.

No therapeutic, fertility, pelvic-health or medical outcome is claimed.

Start with a measured curve profile

Record overall length, usable length, maximum width, tip radius, arc rise and the distance from the tip to the deepest point of the bend. Photograph the approved sample against a dimensioned grid so scale is not inferred from styling.

Choose fit by measurements, not by the apparent size of the image.

The broad tip needs an edge-free transition

Inspect the rounded end under side light and light compression. The outer surface should flow into the shaft without mold flash, a hidden hard rim, thin spots or a seam positioned where pressure concentrates.

Stop for pain, numbness, irritation or persistent discoloration.

Curvature should be stable under light load

Measure deflection at repeatable loads and note whether the bend springs back, stays fixed or contains a flexible internal frame. After cycling, inspect for whitening, creaking, delamination and changes in tip alignment.

Do not force the arc straighter or sharper than its verified range.

The gold collar is decorative only after edge inspection

The crown-like band should sit flush with the green body and base. Check every raised point for radius, coating coverage, gaps and lift after cleaning, sweat simulation and repeated gripping.

Reject chipped plating, sharp peaks, trapped residue or a loose band.

A single button must still provide a clear stop

Map the exact long-press and short-press sequence for power and mode changes. Confirm startup intensity, memory behavior, lock behavior and how quickly the motor stops when the button is held.

Practice the stop action before use so it does not depend on seeing the control.

Ten frequencies remain a source claim

The marketplace page refers to ten adjustable frequencies without a verified waveform table. Record dominant frequency, acceleration and pattern duration for every state, and combine settings that are not meaningfully distinct.

The final listing will publish only the measured mode sequence.

Output should be mapped along the curved body

Measure vibration at the tip, inner arc, outer arc, collar and base with a repeatable compliant load. This shows whether energy stays near the broad tip or travels strongly into the hand.

Listen for collar buzz, internal knocks and speed instability at each state.

Surface claims need lot-linked documentation

The source uses silicone and ABS terminology without evidence tied to an exact revision. Request records for the emerald outer layer, internal structure, button, collar substrate, coating, pigments, seals, adhesive and contact surround.

Check odor, tack, oil bleed, dye transfer, swelling and finish change after conditioning.

Cleaning guidance follows the weakest seam

Map the tip surface, body skin, collar edges, base joint, button and magnetic contacts before writing wash instructions. A smooth main body does not prove that the collar or charging end can tolerate rinsing.

Power off, clean by the confirmed method and dry every recess completely.

Ingress protection cannot be inferred from a sealed appearance

Require model-specific evidence for the outer skin, collar junction, button, base seam and charging contacts. Until that evidence is approved, treat the powered device as non-submersible and keep it away from standing water.

Never charge a damp sample.

Charging tests begin with the white magnetic lead

Confirm input rating, pin polarity, cable length, attachment force, indicator behavior and full-charge time. Test reversed placement, contact bridging and whether the connector detaches cleanly without pulling the device from a surface.

Use only the approved lead with a documented compatible power source.

Thermal checks should follow a loaded operating cycle

Monitor the tip, inner bend, collar, base, battery zone and contacts during charging and continuous operation at the strongest verified state against a compliant pad. Record ambient conditions and the stabilization point.

Stop using a unit with abnormal heat, swelling, odor, noise or erratic control behavior.

The price plan includes curve and collar validation

The Alibaba lead displays USD 6.40 for 10 to 499 pieces and USD 4.80 from 500. Generated marketplace text also presents unverified material and performance statements that are excluded from the product promise.

The procurement reference is a sourcing lead only. The EUR 24.99 plan allows for China-origin freight, a sample, dimension, curvature, collar-edge, vibration, sound, thermal, ingress and material checks; freight, duty, tax, insurance, packaging, payment fees and destination terms remain pending.

This silhouette suits shoppers comparing controlled curves

It is intended for adults who prefer a smooth continuous arc, a rounded contact end and one-handed control. A straight bullet, flexible mini wand or dual-motor rabbit may be more suitable for a narrower point, freer angle changes or simultaneous external contact.

Final fit guidance will follow the approved measurement sheet.

Frequently asked questions

Is the curve flexible?

Its deflection and recovery remain pending mechanical measurement on the production sample.

Are ten modes guaranteed?

No. Ten frequencies appear in the source, but the distinct mode count and sequence require verification.

Is the gold collar metal?

The collar substrate, coating and edge construction remain pending supplier evidence and sample inspection.

Can it be used in water?

No immersion guidance is approved without model-specific ingress evidence for every seam and contact.

What are the exact dimensions?

Overall length, usable length, widths, tip radius and arc rise remain pending measurement.

What should be inspected before operation?

Check the tip, curved body, collar, button, base seam and charging contacts, then confirm low output and immediate stop away from the body.