Front-Clasp Crescent-Lace Bralette, Six-Strap V-Waist Garter Belt and Thong Set

Build a three-piece silhouette around a front clasp

This front-clasp crescent-lace bralette, six-strap V-waist garter belt and thong set concept contains exactly three separate smoky-plum and charcoal garments. The proposed pack combines one wireless triangle-cup bralette, one V-shaped garter belt with six hanging straps and one matching thong.

The image establishes visible styling only. It does not confirm sizes, fibres, opacity, stretch, support, clasp construction, strap range, garter compatibility, gusset, care or production readiness.

Audit the exact three-garment pack

Count one bralette, one garter belt and one thong before sealing. Stockings, robe, gloves, jewellery, shoes, storage bag and other accessories are excluded.

Match all three garments by colour lot, lace motif direction, charcoal trim, thread and hardware finish. Record size and colour codes on the complete set rather than on one loose piece.

Measure both floral-lace triangle cups

Record cup height, base width, apex position, centre spacing, side depth, lace motif placement and lining coverage on left and right. Compare the two pieces for symmetrical cut, seam length and edge scallop.

Wireless, unlined, sheer and supportive descriptions require the approved pattern, layer map and fit evidence; the flat lay alone cannot validate them.

Cycle the centred front clasp

Inspect the small centre-front closure for complete engagement, edge smoothness, alignment and resistance to accidental opening under bounded garment tension. Record clasp width, material, coating, cycle count and any contact point beside the cup bases.

Front-fastening language describes the visible concept only. Exact mechanism, one-hand operation and durability remain pending production samples.

Map the charcoal crescent underbust band

Measure the curved band from each cup edge to the centre clasp and around the unseen rear section. Record width, thickness, extension force, seam placement, edge binding and permanent set after conditioning.

Lift, shaping, support and pressure-distribution claims are excluded until graded fitting and force-extension testing are complete.

Check shoulder straps and rear adjustment

Record both shoulder-strap widths, minimum and maximum working lengths, slider travel, front anchor position, rear attachment and elastic extension. Compare left and right hardware for orientation and smooth travel.

The rear band, closure and adjusters are not visible in the front flat lay. Require a rear technical view and approved finished-measurement sheet before publishing dressing instructions.

Measure the V-shaped garter belt

Record centre-front depth, side height, total top-edge length, V angle, lace panel width, rear construction and waist adjustment. Inspect the centre seam and both hip curves for puckering, broken yarns and uneven trim.

High-waist, low-rise and shaping labels remain pending the approved pattern, graded measurements and intended wearing position.

Number all six hanging straps

Label the front pair G1 and G2, side pair G3 and G4, and outer pair G5 and G6 according to the approved technical diagram. Measure each free length, width, slider travel, attachment point and extension force.

Exactly six straps must be present in every approved set. Reject twisting, mismatched lengths, reversed sliders, weak anchors and uneven spacing outside tolerance.

Inspect the six garter clips

Cycle every terminal clip and record jaw alignment, insert material, opening force, closure retention and edge finish. Test compatibility only against the specified stocking welt thickness without overstretching the lace belt.

Stockings are not included. Clip material, coating, nickel status, maximum compatible welt and durability remain pending supplier evidence.

Map the thong side straps and gusset

Measure front panel height, back coverage, two narrow side straps per side, relaxed and stretched hip range, crotch width, binding and seam bulk. Require a rear view to confirm the back geometry.

Document gusset length, width, fibre content, layer count, lining coverage and attachment stitches. Cotton, breathable, hygienic and moisture-management language is excluded until the final specification and tests are approved.

Identify lace, mesh, elastics and trims

Obtain fibre declarations for the floral lace, mesh ground, crescent band, shoulder straps, garter straps, thong side straps, bindings, thread and gusset. Record mass, openness, extension and set in relevant directions.

Soft, skin-friendly, hypoallergenic, sustainable and certified claims remain pending traceable material documents and applicable testing.

Audit seams, anchors and hardware contact

Map stitch type and density at cup edges, clasp ends, underbust band, shoulder anchors, garter-belt waist, six strap anchors, six clips, thong sides and gusset. Inspect for skipped stitches, sharp thread ends, needle damage and adhesive residue.

Stop wearing the set if a clasp, slider or clip develops a sharp edge, if elastic creates numbness or colour change, or if lace damage exposes hard hardware.

Build size guidance from graded measurements

Measure bralette underband, cup geometry, shoulder-strap range, garter-belt waist, belt depth, each garter length and thong hip range for every offered size. Combine those figures with controlled extension data and approved fitting.

Do not map supplier letter sizes directly to retail, infer cup sizes from width alone or claim one-size suitability without graded samples.

Control colour transfer and delicate care

Test smoky-plum lace, charcoal trim, elastics, thread, gusset and hardware finishes for dry and wet rubbing, perspiration exposure, wash migration and storage contact. Use only a validated water temperature, detergent, agitation and drying method.

Close or protect the front clasp and six garter clips during cleaning if the final care study requires it. Avoid bleach, solvents, wringing, high heat, machine drying and direct ironing unless the approved label explicitly permits them.

Build landed price from public three-piece benchmarks

An Alibaba wholesale-garter-lingerie category page displayed a white lace three-piece bra, garter-belt and underwear set at USD 6.99 to 7.59 with MOQ 1, and another three-piece garter-thong set at USD 7.06 to 7.65 with MOQ 300. These are broad procurement references, not this exact front-clasp six-strap construction or an approved supplier.

The public procurement benchmark supports an EUR 44.99 planning price after provisional allowance for China-origin freight, graded samples, three-garment picking, lace, elastics, front clasp, six straps and clips, gusset, colourfastness and care validation, discreet fulfilment and expected apparel handling loss. Exact supplier, quote, MOQ, sizes, colours, fibres, packed weight, freight, duty, tax, certification, payment terms and lead time remain pending.

Frequently asked questions

How many garments are included?

Exactly three: one bralette, one garter belt and one thong.

How many garter straps are attached?

Exactly six straps are planned on the separate V-waist belt.

Are stockings included?

No. Stockings and other styling accessories are excluded.

Does the bralette fasten at the front?

A centred front clasp is shown, but the final mechanism and closure range remain pending approved samples.

What sizes will be offered?

The size range and every graded measurement remain pending supplier confirmation and fitting.

How should the set be washed?

Follow only the validated care label for the approved lace, elastics, hardware, thread and gusset.