Fuchsia U-Shape Wearable Couples Vibrator with Fan-Groove and Triple-Groove Paddles

Trace this fuchsia U-shape design to one exact listing

This fuchsia U-shape wearable couples vibrator follows one identified supplier listing rather than a generic catalogue silhouette. Across six collected source images, the repeated identifiers are a continuous curved bridge, one broad rounded paddle with fan-like shallow channels, one narrow oval paddle with three lengthwise grooves, a recessed button and two charging contacts.

The public image is newly created from the visible construction. Supplier photographs remain in the private procurement record while media rights are documented.

Use the broad fan-groove paddle as the primary match point

The wider end has a rounded leaf-like outline and several shallow channels spreading from the bridge area. Incoming samples should be photographed from front, side and rear, then compared for outline, groove count, groove direction, edge radius, surface finish and the transition into the bridge.

A smooth substitute without this fan arrangement, or a round, butterfly or three-lobe head, is not the selected product.

Check the narrow paddle for exactly three long grooves

The smaller end is elongated rather than circular and carries three shallow longitudinal grooves on its visible face. Record overall length, maximum width, thickness, groove depth, groove spacing and tip radius from the approved sample.

The dimensions cannot be inferred reliably from a styled marketplace image, so the final specification remains pending measured units.

Measure the continuous curved bridge under controlled loads

Document relaxed span, internal clearance, outside curve, cross-section and deflection at several repeatable forces. Cycle the bridge and inspect whitening, cracking, permanent set, surface separation and change in paddle alignment.

Flexibility is visible as a design intention, but wearable fit, pressure and retention must be evaluated with consent-based fit protocols before sales guidance is published.

Map the recessed button and two charging contacts

The broad paddle’s reverse side shows one small recessed control and two exposed contacts. Confirm button travel, activation sequence, indicator behaviour, accidental-press resistance, contact spacing, corrosion resistance and the exact charging accessory supplied with the selected option.

No cable, magnetic lead, dock or adapter is promised until the sealed packing list and electrical sample agree.

Validate app pairing before describing remote control

The supplier title and graphics describe app control and long-distance operation. Verification must capture the app name, publisher, current store availability, account requirements, permissions, pairing route, local-control fallback, operating-system versions, range and behaviour after a dropped connection.

Privacy terms, data location, update policy and vulnerability handling also need review; app operation is therefore a pending supplier claim.

Confirm the claimed nine patterns on production firmware

Supplier graphics mention nine modes. A received unit should be logged pattern by pattern using both the physical button and app, checking order, restart state, independent control, intensity steps and whether marketing counts speeds and patterns consistently.

The public page does not guarantee a mode count until production firmware, instructions and repeated samples match.

Evaluate wearable fit without assuming universal anatomy

Assess contact placement, bridge pressure, movement stability and access to the control across a documented range of fit fixtures and voluntary adult wear trials. Record where clothing changes placement or app access, and stop any trial if pinching, numbness, excessive pressure or discomfort occurs.

Fit is individual; the two unequal paddles do not establish suitability for every body or activity.

Measure operating sound in a repeatable room setup

The supplier graphic states below 60 dB, but it does not show the test distance, room noise, mounting, mode or meter settings. Measure each approved unit at defined distances in free air and in representative contact conditions, and publish only comparable results.

Quiet, silent and discreet-performance language stays withheld until a recorded protocol supports it.

Verify ingress resistance before any cleaning claim

IPX6 appears in supplier artwork. Request a lot-matched report covering the complete assembly, then inspect the button area, seam, charging contacts and any hidden openings after the appropriate controlled test.

Until evidence is accepted, keep the device, charging contacts and power source away from immersion. Final cleaning instructions must come from validated materials, ingress tests and the approved manual.

Obtain complete material and skin-contact declarations

Request polymer names for each coloured and internal component, pigments, adhesives, coatings, metals, restricted-substance records, odour limits and batch traceability. Compare surface tack, hardness, finish and colour consistency across samples.

Silicone, body-safe, hypoallergenic, latex-free, phthalate-free and medical-grade descriptions are not used without matching evidence.

Test charging battery and electrical protection

Record input voltage and current, connector polarity, charge time, usable runtime by mode, standby drain, low-power indication, temperature rise, overcharge response, short-circuit protection and battery identification. Repeat the test after controlled cycles rather than relying on one new unit.

Supplier artwork mentions USB charging, while the exact cable, battery capacity and electrical conformity remain pending.

Lock the proposed pack only after a sealed sample arrives

The current planning unit contains one fuchsia U-shaped device. Instructions, charging lead, storage item, packaging, app leaflet and any other accessory are excluded from the promise until the selected colour option’s packing list and sealed sample confirm them.

Retail packaging also needs discreet labelling, barcode space, tamper evidence and destination-language review.

Reject substitutions that break the source fingerprint

Quality control should compare colour, continuous bridge, broad fan-groove paddle, narrow triple-groove paddle, recessed button and two contacts against the approved golden sample. Lot checks should also cover seams, surface defects, odour, control logic, pairing, output consistency, charging and pack count.

Rabbit ears, rings, bullets, T-bars, separate controllers, three-lobe heads or changed groove layouts require a new SKU and fresh sourcing record.

Plan EUR 39.99 from a provisional landed-cost model

The hidden procurement record stores Shenzhen Xindeli Technology Industrial Co., Ltd., listing ID 1601596097159, the observed EUR 2.32-2.61 reference range, MOQ three pieces and the check date. The marketplace page also displayed 146 sold; none of these observations is a binding quotation or performance warranty.

EUR 39.99 is a planning retail price allowing for China-origin freight, app and electrical checks, ingress and sound validation, discreet fulfilment and expected quality loss. Packed weight, destination freight, duty, tax, payment terms, lead time, current option price and final landed cost remain pending.

Frequently asked questions about this U-shape vibrator

Is app control already confirmed?

No. The supplier listing claims app control, while app identity, pairing, permissions, range, privacy and supported systems still require live validation.

Does it definitely have nine modes?

Nine modes appear in supplier graphics, but the production firmware and instructions must be tested before that count is promised.

Is it waterproof?

No public waterproof claim is approved. The advertised IPX6 level needs a lot-matched report and a complete-device test.

What material touches the body?

The exact polymers, pigments, coatings and adhesives are pending a supplier bill of materials and sample review.

What comes in the box?

Only one fuchsia device is in the planning unit; instructions, charging lead and all other pieces await the sealed packing list.

Will the U-shape fit everyone?

No wearable geometry fits every body. Bridge span, pressure, placement and retention need measured samples and individual fit evaluation.