Three-Leaf Split-Crown Rabbit Vibrator with Triple-Groove Thumb Rest and Dual Oval Controls

Split the short external crown into three flexible leaves

This three-leaf split-crown rabbit vibrator concept combines one softly curved smoky-plum main stem with one shorter offset arm. The arm ends in exactly three narrow leaf tips, while a charcoal thumb rest with three grip grooves and two oval buttons organizes the handle.

The image fixes external geometry only. Dimensions, materials, motors, output, flexibility, charging and ingress protection remain pending.

Define a single-device inventory

The proposed sales unit contains exactly one powered vibrator. A charging cable, adapter, storage pouch, remote, interchangeable head, sleeve and lubricant are excluded unless an approved packing list adds them.

Every included electrical item and printed instruction must be matched to the exact production revision before sale.

Curve the main stem without hiding usable measurements

Publish total length, usable length, maximum diameter, minimum neck diameter, centreline curvature and product mass. Record both free shape and deflection under controlled side loads so the page does not rely on appearance alone.

The curved profile is a design direction, not a fit promise for every body.

Round the main head into one broad oval dome

Measure head length, width, edge radius and transition into the shaft. Inspect mould seams, coating changes and local hardness across the dome, especially where the curve produces a thinner wall or concentrates bending stress.

No rotation, thrusting, heating or moving bead function is promised.

Offset the shorter arm from a reinforced root

Record branch angle, root thickness, free length and clearance from the main stem. Cycle the arm forward, backward and laterally while inspecting the junction for tearing, whitening, delamination or internal component movement.

The arm position must be documented across production tolerances because small angular changes can alter contact alignment.

Count and control exactly three leaf tips

Specify leaf length, width, thickness, edge radius, spacing and free angle for the left, centre and right tips. Check that all three remain separately visible and do not fuse, twist or overlap after moulding and conditioning.

No fourth leaf or twin-petal insert is included, distinguishing this model from the earlier two-petal offset-arm concept.

Measure leaf flex as three individual cantilevers

Apply equal loads to each tip and compare displacement, rebound time and permanent set. Repeat with the outer pair loaded together, then inspect whether one leaf shadows another or transfers force into the branch root.

Softness and flexibility claims require numerical ranges from approved samples.

Use the thumb rest as a grip reference

The charcoal oval rest carries exactly three shallow horizontal grooves. Measure groove depth, spacing, edge radius and surface friction under dry and lubricated handling, then test different grip orientations without forcing the wrist into one position.

The rest is not a separate control and must not be described as a pressure sensor.

Separate two oval controls by function and feedback

Map power, pattern and zone selection only after firmware is fixed. Record press force, long-press timing, debounce behaviour, tactile feedback, status indications and accidental activation during storage.

Independent motors, mode counts, memory and travel lock remain unconfirmed until an engineering sample demonstrates them.

Characterize output at the dome branch and leaves

Measure frequency, acceleration and amplitude at the main head, branch root and each of the three leaf tips across every verified setting. Test free-running output and controlled loads so published comparisons reflect real contact conditions.

Claims about intensity, quietness or dual-zone independence remain withheld without measured evidence.

Validate battery charging and idle protection

Request cell chemistry, rated capacity, charge input, charge time, runtime test method, low-voltage cut-off, over-current protection, transport documents and storage guidance. Repeat charge-discharge cycles on multiple samples while monitoring swelling and temperature.

USB type, cable inclusion, runtime and standby duration remain pending the approved bill of materials.

Verify materials seams and ingress as one enclosure

Obtain composition, hardness, pigments, adhesives and restricted-substance documentation for every touch surface and internal enclosure part. Inspect mould lines around the leaves, branch, controls and base before and after flex cycling.

Silicone, ABS, phthalate-free, latex-free, hypoallergenic, body-safe and waterproof claims remain withheld without traceable reports and complete-device testing.

Measure sound temperature and enclosure stability

Record sound pressure at a defined distance in a controlled room, then repeat under standardized loads. Log surface and internal temperature during continuous operation, charging and blocked-motor fault tests.

Stop use if output becomes erratic, the enclosure opens, controls jam, odour develops or any surface becomes unusually warm.

Build cleaning and risk guidance from verified limits

Clean only with methods compatible with the confirmed materials and ingress rating, paying attention between the three leaves and around both buttons. Rinse residues where permitted, dry fully and inspect the branch root and seams before storage.

Do not share without an appropriate barrier and validated cleaning process. Stop if discomfort, irritation, numbness, swelling, bleeding or surface damage occurs; medical claims are not made.

Plan price from rabbit-vibrator benchmarks and landed reserves

An Alibaba rabbit-vibrator USB page displayed a rechargeable reference at USD 6.69 to 6.99 with MOQ 2, a heated reference at USD 8.69 to 8.99 with MOQ 2 and a factory rechargeable reference at USD 11.90 to 14.90 with MOQ 1. A dual-rabbit page displayed a rechargeable dual-motor reference at USD 6.80 to 7.50 with MOQ 3. These are broad category examples, not quotations for this three-leaf design or approved suppliers.

The public procurement benchmark supports an EUR 54.99 planning price after provisional allowance for China-origin freight, custom three-leaf moulding, independent leaf-flex checks, output and battery validation, material and ingress testing, discreet fulfilment and expected electronic quality loss. Exact supplier, quote, MOQ, dimensions, materials, motors, battery, cable, packed weight, freight, duty, tax, certification, payment terms, lead time and production availability remain pending.

Frequently asked questions about the three-leaf rabbit vibrator

How many leaf tips does the short arm have?

Exactly three separate tips are proposed, with final dimensions and flexibility still requiring sample tests.

Does it have two motors?

Motor count and independent-zone behaviour have not been confirmed.

How many control buttons are shown?

Exactly two oval buttons are visible below the charcoal thumb rest.

Is it waterproof?

No ingress rating is claimed until the complete charged enclosure passes a documented test.

What material covers the product?

No surface material has been verified, so silicone and body-safe claims remain pending.

Does it include a charging cable?

Cable type and pack contents require the approved production packing list.