Hexa-Facet Tapered Suction-Base Dildo

Read six long faces as one restrained geometric form

This hexa-facet tapered suction-base dildo concept uses six long flat longitudinal faces around one tapered deep-plum body, ending in a softly rounded tip above a broad smoky-charcoal suction base with one release tab.

The rendering defines visible architecture only. It does not confirm dimensions, insertable length, composition, hardness, edge radii, moulding, suction capacity, cleanability or production readiness.

Confirm one-piece construction and pack contents

The proposed inventory is one non-powered product with one faceted body, one integral base and one release tab. No motor, core, battery, remote, harness, pouch or detached accessory is shown.

Request a section drawing and approved pack list that identify every material layer, colour boundary, mould gate, reinforcement and label.

Measure the rounded taper from fixed datums

Record total height, insertable boundary, usable length, tip radius, cross-section at regular intervals, maximum across-flat and across-corner widths, neck transition, base diameter, base thickness, release-tab size and mass. Define datums on the base plane and central axis.

Rendered proportions are not a sizing specification and must not be used to infer fit.

Map all six faces and their edge radii

Label the faces F1 through F6 around the body. Measure face width, taper angle, flatness, colour consistency and longitudinal alignment, then gauge every intervening edge radius from tip to base.

Reject sharp arrises, edge notches, wavy planes, collapsed corners or asymmetry that concentrates pressure beyond the approved fixture limit.

Compare across-flat and across-corner pressure

Use graded compliant forms to map pressure with a face centred, an edge centred and intermediate rotations. Record insertion force, withdrawal force, rotation torque, local compression and how the taper changes contact along the verified boundary.

A hexagonal profile can feel different by orientation; comfort claims require controlled evidence and consenting-adult evaluation only after material approval.

Verify softness at faces edges and core

Measure Shore hardness and compression at the centre of each face, beside every edge, near the tip, at the neck and above the base. Repeat after conditioning, cleaning and bounded flex cycles.

Terms such as soft, firm, dual-density or flexible remain pending because appearance cannot establish mechanical response or internal reinforcement.

Inspect moulding seams gates and colour boundaries

Review the full surface under magnification for flash, sink, voids, bubbles, contamination, tack, exposed reinforcement and abrupt colour steps. Identify parting lines and gate locations before approving a cleaning method.

Every face and edge should remain visible and accessible without unverified disassembly.

Test suction on documented surface classes

Measure attachment and release on clean dry glass, glazed tile and other supplier-approved non-porous surfaces using fixed preparation, dwell and pull protocols. Repeat with centred, angled and bounded cyclic loads.

Suction performance varies with surface condition, dust, cleaner residue, moisture, temperature, tab geometry and base ageing; do not promise universal attachment.

Keep the release tab accessible under load

Record tab direction, grip area, peel force and release time while the product is unloaded and under conservative offset fixture loads. Inspect the tab root and base rim for tearing, whitening and permanent curl.

Use only a hand-controlled setup that permits immediate release. Never mount where detachment could cause a fall, impact or loss of control.

Request exact composition and restricted-substance evidence

Obtain outer and internal compositions, pigments, additives, cure or mould process, restricted-substance reports, lot traceability and odour criteria. Match every document to the sellable colour and construction.

Silicone, body-safe, non-porous, hypoallergenic, latex-free and phthalate-free claims remain unavailable until exact-model evidence is approved.

Start slowly and keep the full base outside

Inspect the tip, all six faces, edge radii, neck, base and release tab before use. Apply a compatible lubricant only after composition evidence is known, begin gradually and keep the broad base completely external and reachable.

Stop for pain, numbness, bleeding, unusual pressure, loss of control, material damage or a base that no longer remains accessible. Persistent symptoms require appropriate medical advice.

Choose cleaner and lubricant by compatibility testing

Test candidate cleaners and lubricants on approved samples for swelling, mass change, tack, hardness drift, colour transfer, cracking and surface-energy change. Include the face edges, colour transitions, base rim and tab.

Oil, solvent, bleach, boiling, dishwasher cleaning and abrasive tools are excluded unless model-specific evidence supports them.

Wash every flat face and dry every junction

Follow the validated water temperature, cleaner concentration, contact time and rinse method. Clean F1 through F6 separately, then wipe the rounded tip, all longitudinal edges, neck, base underside, rim and release-tab root.

Dry the product fully in open air away from heat and sunlight, paying particular attention to the body-to-base junction and underside recess.

Store upright only when the base remains unstressed

Use the documented storage position that avoids bending the shaft, flattening an edge or leaving the suction cup under continuous preload. Keep it separate from incompatible materials, dyes, dust and sharp objects.

Inspect for facet distortion, tack, odour, discolouration, cracks, base curl and tab damage before each later use.

Build landed price from a suction-dildo benchmark

An Alibaba suction-dildo category page displayed one mini beaded suction-base example at USD 1.49 to 2.80 with MOQ 1. It is a broad procurement benchmark only and does not identify this six-face geometric design or an approved supplier.

The public procurement benchmark supports an EUR 34.99 planning price after provisional allowance for China-origin freight, exact-sample measurement, facet and edge inspection, hardness, pressure, moulding, composition, suction, cleaner and lubricant compatibility tests, discreet fulfilment and expected handling loss. Exact supplier, quote, MOQ, dimensions, materials, packed weight, freight, duty, tax, certification, payment terms and lead time remain pending.

Frequently asked questions

How many longitudinal faces does the body have?

The concept has a hexagonal cross-section with exactly six long flat faces separated by softly radiused edges.

Is the shape anatomically realistic?

No. It is an abstract tapered geometric form with no anatomical detailing.

What are the exact dimensions?

Total height, insertable boundary, across-flat width, across-corner width and base measurements remain pending approved samples.

Which lubricant is compatible?

Compatibility depends on verified composition and must be established by sample testing before guidance is published.

Will the suction base stick to every surface?

No. Attachment depends on the approved surface class, cleanliness, preparation, load and base condition.

Which material is used?

Exact outer and internal compositions, pigments and restricted-substance evidence remain pending supplier documentation.