Shared-Remote Wearable Egg and Open Couples Ring Set

Coordinate an egg and open ring from one remote

This shared-remote wearable egg and open couples ring set concept contains exactly one smoky-plum egg vibrator, one open flexible vibrating ring and one charcoal-and-plum two-button remote. The egg has a broad flattened retrieval tail; the ring presents a raised oval external pad and quick-grip tab.

The image establishes proposed count and form only. It does not confirm dimensions, fit, materials, vibration output, wireless routing, battery, ingress protection or sale-ready production.

Audit exactly three devices before packing

Label the wearable egg E1, open ring R1 and remote RC1. Confirm one of each and verify that E1 and R1 are paired only to the approved RC1 control protocol.

Reject tears, cuts, sticky surfaces, distorted openings, loose pads, damaged cases, incomplete moulding, sharp flash, unreliable buttons or a pairing light that does not follow the approved sequence.

Measure the egg and flattened retrieval tail

Record egg length, maximum diameter, tip radius, tail length, tail width, tail thickness, bend radius and mass. Measure tail pull strength, flex recovery and permanent set after repeated cycles.

Compact, wearable and low-profile claims remain pending finished dimensions and approved fit testing.

Keep the egg retrieval tail external

For approved vaginal wear, perform an external fit check, use only validated compatible lubricant and keep the full flattened tail outside the body and readily controllable. Remove it slowly by the tail, never by a sudden pull.

The egg has no flared anal base and must not be used anally. Stop for pain, numbness, bleeding, unusual pressure, loss of tail control or any concerning response.

Grade the open ring without assuming universal fit

Record relaxed inner opening, maximum approved opening, band width, band depth, gap width, restoring force and recovery at controlled extension. Map pressure around both arms rather than relying on one nominal diameter.

Universal, one-size, circulation-safe and extended-wear claims are excluded until graded fit and bounded-duration studies are approved.

Characterize the raised oval contact pad

Measure pad length, width, height, edge radius, motor position, surface texture and deflection under load. Confirm that its output remains stable while the open ring is at each approved extension.

External contact varies with anatomy and position; no guaranteed contact point or outcome is claimed.

Use the quick-grip tab for prompt removal

Measure tab width, thickness, texture, bend strength and clearance from the ring gap. Verify a gloved and wet grip without creating a sharp edge or pinch point.

Remove the ring immediately for numbness, coldness, discolouration, pain, swelling or loss of normal sensation, and seek medical advice for persistent symptoms.

Map both remote buttons and pairing light

Document button press duration, device selection, intensity step, pattern step, power-off command, lockout, pairing indication and low-battery state. Make the stop command available from every control state.

The two-button appearance does not establish mode count or independent control; final behaviour remains pending firmware approval.

Verify one-device and two-device routing

Test whether RC1 selects E1, R1 or both, and confirm the state through an unambiguous indicator before body contact. Measure command latency, missed commands and unintended cross-control around other units.

Independent channels, synchronized patterns and long-distance range are excluded until the final radio and firmware are validated.

Measure motor output in both devices

Characterize frequency, acceleration, displacement, sound and thermal rise for E1 and R1 under repeatable contact loads and across the battery discharge curve. Compare output when one or both devices are active.

Powerful, deep, quiet and whisper-quiet language remains pending calibrated test results.

Require exact material and hardness evidence

Obtain polymer names, supplier grades, additives, pigments, bonding methods and hardness values for the egg, tail, ring, pad, tab and remote surfaces. Test the final coloured assemblies after cleaning and ageing.

Silicone, body-safe, hypoallergenic, phthalate-free, nonporous and skin-friendly claims remain pending traceable finished-product evidence.

Validate batteries charging and radio compliance

Require cell chemistry, capacity, protection circuits, charge inputs, cable specification, charge time, runtime, standby draw, transport documents, radio band and regional compliance. Test both devices and RC1 separately.

Rechargeable, wireless range and runtime claims remain pending production electronics, approved chargers and representative-use tests; no charging cable is shown in the planned visual inventory.

Separate cleaning from powered components

Switch off and unpair both devices before cleaning. Validate cleaner concentration, contact time, rinse, drying and disinfection limits for E1 and R1, while RC1 receives only its approved wipe method.

Never immerse RC1, and do not immerse either vibrator unless its finished assembly passes the declared ingress test. Dry all seams and charge contacts completely before charging.

Set consent hygiene and inspection boundaries

Agree who controls RC1, establish a stop signal and keep immediate manual access to both devices. Clean before first use and between partners or use a compatible barrier where appropriate.

Inspect the egg, tail, ring gap, pad, tab, seams and controls before every session. Discontinue any cracked, torn, swollen, sticky, distorted, overheating or unreliable part.

Build landed price from two category benchmarks

Alibaba category pages displayed one remote vibrating egg at USD 4.20 to 4.90 with MOQ 5 and one rechargeable couples ring at USD 5.90 to 6.53 with MOQ 16. They are separate broad benchmarks, not this shared-remote set or an approved supplier quote.

The egg benchmark and ring benchmark support an EUR 69.99 planning price after provisional allowance for China-origin freight, shared control, dual-device motor and radio validation, materials, fit, battery, ingress and cleaning tests, discreet fulfilment and expected quality loss. Exact supplier, quote, combined MOQ, dimensions, materials, modes, range, batteries, charging accessories, packed weight, freight, duty, tax, certification, payment terms and lead time remain pending.

Frequently asked questions

What is included?

Exactly one wearable egg vibrator, one open vibrating couples ring and one shared two-button remote.

Can the egg be used anally?

No. It lacks a flared anal base and is not approved for anal use.

Does the remote control each device separately?

Device selection and shared-operation behaviour remain pending the approved firmware and pairing tests.

How long can the ring be worn?

No wear duration is approved until fit, pressure and circulation-related risk controls are validated.

Are charging cables included?

The charging specification and accessory inventory remain pending and no cable is shown in the concept image.

Can all three devices be rinsed?

No. The remote requires wipe cleaning, and either vibrator may be rinsed only after its ingress rating and care method are verified.